Search found 45 matches

by raphnou
Sat Jul 07, 2018 7:41 am
Forum: Direto
Topic: Elite Direto - no resistance and strange clicking noise
Replies: 11
Views: 662

Re: Elite Direto - no resistance and strange clicking noise

Hello, I went on the side of the dark force and my feeling is that I did very well. The reliability of the Direto does not seem to me to the height for 4 training per week, the design of the belt tensioning roller is its weak point, the bearing is too small, sooner or later everyone will have these ...
by raphnou
Fri Jun 08, 2018 12:50 pm
Forum: Direto
Topic: Elite Direto - no resistance and strange clicking noise
Replies: 11
Views: 662

Re: Elite Direto - no resistance and strange clicking noise

Alas the Direto is gone today! :cry: But now I understand why the calibration drifted down every week and the popping noises. The damaged belt loses its resistance to the rhythm of the sessions and the calibration was always on the decline. The Assitance Elite, so offered me to adjust the belt, but ...
by raphnou
Thu Jun 07, 2018 7:23 pm
Forum: Direto
Topic: Elite Direto - no resistance and strange clicking noise
Replies: 11
Views: 662

Re: Elite Direto - no resistance and strange clicking noise

Hello Elite, I bought the Direto the 12/04/18 I use it 4 times a week. I just finished a long session of 1h30 on Zwift, at the end of the session the Direto made noises of "clack" several times and now it is hard all the time, the pedaling is not at all fluid it is jerky, and the direto no...
by raphnou
Tue Jun 05, 2018 7:42 am
Forum: My e-training Desktop
Topic: intervals with MyETraining training mode
Replies: 1
Views: 185

intervals with MyETraining training mode

Hello Elite, For what reason does MET in training mode still not allow to mark the intervals automatically? Zwift does it, garmin does it, when we do a training the goal is still to be able to analyze each interval separately, MET systematically export a TCX file with a single interval ... Have a go...
by raphnou
Mon Jun 04, 2018 5:52 pm
Forum: Direto
Topic: Direto power off by around 50 watts
Replies: 32
Views: 3558

Re: Direto power off by around 50 watts

We check the tension of the belt unit by unit here in our factory. But it may happen - especially with time - that the belt loose a little bit of power, due to usage. This will cause a drop in the offset value. In your case, I don't think this is the problem (it's not possible that the belt is loos...
by raphnou
Mon Jun 04, 2018 4:37 pm
Forum: Direto
Topic: Latency of the direto in ERG mode with Zwift
Replies: 6
Views: 367

Re: Latency of the direto in ERG mode with Zwift

Hi Direto adjusts resistance using a stepping motor. When requested power/slope changes, the motor moves a magnetic arm to match the requested value. Of course this movement requires some seconds. Also, the software will add other seconds of delay (it has to verify the data, see the variation, send...
by raphnou
Fri Jun 01, 2018 3:58 pm
Forum: Direto
Topic: Latency of the direto in ERG mode with Zwift
Replies: 6
Views: 367

Re: Latency of the direto in ERG mode with Zwift

Hi, I repeat my graph above, to add a precision. I took the selection # 1 which corresponds to the points in the Direto precision range which is +/- 2.5% or according to the requested power 210w. The range of points is between 204.75w - 215.25w First observation, the average power of the selection #...
by raphnou
Thu May 31, 2018 2:44 pm
Forum: Direto
Topic: Latency of the direto in ERG mode with Zwift
Replies: 6
Views: 367

Latency of the direto in ERG mode with Zwift

Hello Elite, Here is the graph of an easy 30x30 sceance in Zwift (155W / 210W) @ 100rpm each point corresponds to one second We can determine the Direto latency time of about 7/8 seconds at the ramp up, there is also a latency at power release. With a precise power sensor, the latency is a decisive ...
by raphnou
Thu May 31, 2018 2:26 pm
Forum: Direto
Topic: Direto power off by around 50 watts
Replies: 32
Views: 3558

Re: Direto power off by around 50 watts

Guys, this is NOT a standard maintenance operation. Tighten the belt is a totally exceptional operation. That's why we ask you to do it only under our supervision and only after we've verified that it is needed. About the spare parts, don't worry about this. We always continue the assistances on ou...
by raphnou
Tue May 29, 2018 4:40 pm
Forum: Drivo
Topic: Terrible sound from my drivo
Replies: 3
Views: 240

Re: Terrible sound from my drivo

Hello,

If I can afford it,
For the next version of the drivo, plan a hole for access and lubrication of the belt and which will be far from the electronic card.
Add a cap like this to close it ;)

is it a flat or notched belt?

Go to advanced search